Troy Bilt Weedeater Repair Manual
Parts, manuals & diagrams for any TROYBILT Line. Troy-Bilt's TB675 EC 4-cycle gas weed trimmer features the new Click N Trim™ bump head, making line.
. 4 Answers SOURCE: One of the problem could be is you have one of the line in this case top line in the carburator clog. For clean the carburator You need to remove first the cover for the filter 2 screws on front of the carburator remove lines mark the lines top and bottom remove slowly the carburator be careful with the gasket.
The carburator have 4 little screws removed and remove the black gasket (diaphragm) clean with carburator cleaner and air, blow air thru the top line tube, now on the otherside remove the screw and clean the gasket and the carburator inside do the same step. Make sure you clean the fuel filter inside the tank with carburator cleaner. Posted on Apr 24, 2010.
246 Answers SOURCE: Hello: The Following is a General Instruction File I Made to Perform this Repair. If you have Any Suggestions or Remarks, then Please Let me Know.Remove the Boom/Shaft from the Engine. Remove the Mounting Bolts and the Boom and Center Drive Shaft should Slide Away from the Starter Housing Assembly.On Some Model Trimmers, there is a Torx Screw Inside the Coupling Drive that has to be Removed.There is also a Locking Screw on the Side of the Housing that is a Anti-Vibration Lock. Using the Breakdown as a Guide Remove the Starter Housing Assembly from the Engine Assembly. Now Carefully/Slowly Remove the Pressure Plate Assembly from the Starter Housing. The Spring May have Broken and Sometimes a Section will Jump Out when the Pressure Plate Assembly is Removed from the Starter Housing. When it Jumps, it Pushes the Recoil Pulley Out Also.
Look at the Direction of the Coil of the Spring in the Housing and Make an Arrow in the Direction of the Coil with a Magic Marker on the Inside of the Housing. Remove the Broken Spring and Clean the Housing with Spray Lubrication. You can Use Solvent if Required, Just be Sure to Wipe it Before Assembly with Spray Lubricant. The New Spring should come with a Retainer that Holds it in a Circle. If you have Removed the Spring from the Retainer, then Use a Piece of Plastic Pipe About 2' Long that is the Same Inside Diameter as the Retainer (Slightly Smaller than the Recess that the Spring Coils Into if you Lost the Retainer).
Coil the Spring Into the Pipe and then Set the Spring Into the Recess. Make Sure the Spring Tab of the Spring Engages the Spring Lock in the Recess. Use a Socket to Hold the Spring in Place and Pull the Pipe Out of the Recess. Lock the Pulley in Place. Now Turn the Pulley in the Same Direction that the Pulley would Turn if the Rope was Turning it. Once the Pulley will Turn No More, then Reverse Direction 1 or 2 Turns and Thread the New Rope Through the Hole in the Center of the Pulley and Out the Hole in the Blower Housing.
Pull the Rope Through Until it is Tight Against the Pulley. Now Tie a Slip Knot in the Rope to Hold the Pulley in Place While the Handle is Attached to the Rope. Once the Handle is Attached, Release the Slip Knot and the Rope Should Retract Into the Housing.
Reassemble the Blower Housing Onto the Engine. On Some Models you May have to Install the Rope Before you Lock the Pulley in Place. If So, there is a U in the Pulley that the Rope is Held in While Turning the Pulley to Tighten the Spring. Go to this Site Addy, and Select Shop Online Parts Look Up. Then Select the Model Tab and Enter the OEM (Troy Bilt)and the Model Numbers. Now Double Click on your Model in the Results Area.
Please, Do Not Hesitate, If you Hit a Snag or this Does Not Correct the Problem, I am Here if You Require More Assistance. Hope this Helps.
Troy Bilt Weed Eater Repair Manual
Let me Know What Happens, Please. May the All Mighty Bless You and Yours.
Troy Bilt Weed Trimmer Troubleshooting
Be Safe and Be Happy. Good Luck Respectfully jbridger (John) Posted on May 11, 2009.
Troy-Bilt weed eaters are versatile pieces of yard equipment. Some have the capability to use different types of cutting attachments to handle tougher brush-cutting jobs around the home.
Whether you are switching out cutting attachments or making repairs to the trimmer head, it is necessary to prevent the head from rotating. Troy-Bilt includes a locking rod tool to lock the shaft of a Troy-Bilt weed eater. The tool inserts through two holes between the guard and the head.
2017 Audi A8 / S8 — Owner's Manual. Posted on 17 Mar, 2017. Model: 2017 Audi A8 / S8 Pages: 354. File size: 89 MB. Download Manual. Online Viewer. 
The tool looks similar to a long piece of bent rod. Things You'll Need.